Block Scene Button| The
block manages four light scenes of a room: H (High), M
(Middle), L (Low, dimmed) and O (Off). Each scene defines a
value for each channel – percent for a dimmer, On or Off for a
switched light. The scenes are recalled by the push button (short), by a KNX scene, by On/Off, by schedules, on a change of presence and from the control. A long key press saves the current light into the scene. The four LED outputs show at the push button what the next key press does: while the light is on, LED O (switch off) lights up; while the light is off, the LED of the scene suggested for the time of day. The times of day are set by the user in the control. As with all block function blocks, presence comes from the block Block Presence. See also Presence general. The matching control is Block Scene Button. Scene values, light groups, LED suggestion, schedules and presence are set there; the block has to be linked to the control. |
|
1. Create the block and set the Number of channels. 2. Link the outputs G1 … to the switching or dimming addresses of the lights. A bit address is switched, any other address is dimmed (0…100 %). 3. Generate addresses: this creates the key inputs, scene, On/Off, dim and the LED and status outputs. No addresses are created for the brightness and the channels. 4. In the ETS assign the push buttons to these addresses: short to Key short, long to Key long, the LEDs to LED H … LED O. The values belong to the address of a channel, not to its position: if the outputs are reordered later, the scene values move along. A newly linked channel gets the defaults 100 / 60 / 20 / 0 % or On / On / Off / Off. |
Inputs |
||
| HK MK LK OK |
Key H/M/L/O short | Optional. Recalls the scene. Every write telegram is evaluated, whatever its value – push buttons often send the same 1 on every press. Responses to read requests have no effect. With a drawn connection a change to non-zero takes effect. Not linked: the scene is only recalled by the other means. |
| SH SM SL SO |
Key H/M/L/O long | Optional. Saves the current light into the scene: the value of each channel used in the room. Every write telegram is evaluated; if the bus repeats the telegram within two seconds, it is saved only once. Not linked: the scene is never saved at the push button – only from the control. |
| SZ | Scene | Optional. KNX scene (DPT 18.001): value 0…63 stands for scene 1…64, bit 7 (+128) for save. The scene with the number Scene number H recalls H, the next three M, L and O. Other numbers are ignored. Every write telegram is evaluated. Not linked: no effect. |
| EA | On/Off | Optional. Non-zero recalls the suggested scene (the one whose LED is lit), 0 recalls O. Every write telegram is evaluated. For a toggle push button use the output LA as feedback. Not linked: no effect. |
| DI | Dim | Optional. Relative dimming (4 bit, DPT 3.007) of all dimmed channels used in the room: bit 3 = brighter, bits 0…2 the step (1 = 100 % to 7 = 1.5 %), 0 = stop. Dimming runs in steps of 5 % every 0.2 seconds. Switched channels stay unchanged; when dimming down a channel that is off stays off. Not linked: no effect. |
| HE | Brightness | Optional. Brightness in lux for the condition If bright / If dark of schedules and presence. Not linked: the condition is not offered, schedules and presence always switch. |
Outputs |
||
| LH LM LL LO |
LED H/M/L/O | LED at the push button. Light on: only LO is 1. Light off: only the LED of the suggested scene is 1. After the controller starts all four are sent once, otherwise on change. |
| AS | Active scene | 0 = light off, 1 = H, 2 = M, 3 = L, 4 = changed by hand (the light is on but matches no scene). Dimmed channels may deviate by 2 %. |
| VS | Suggestion | Scene suggested for the time of day: 1 = H, 2 = M, 3 = L. |
| LA | Light on | 1 as soon as a channel used in the room is non-zero. |
| G1 … | Channel 1 … | One light or light group each. Values are only sent when a scene is recalled and while dimming; afterwards the light may be operated otherwise. The value received on the address counts as the actual value – Light on and changed by hand are derived from it. A channel without an address is not offered in the control. |
Parameters |
||
| Number of channels | Number of outputs G1 … G16, default 4. | |
| Scene number H | KNX scene number for H at input SZ (1…61, default 1). M, L and O follow with the next three numbers. | |